Otis Gun Care
+ Reply to Thread
Page 2 of 3
FirstFirst 1 2 3 LastLast
Results 11 to 20 of 29

Thread: Sported Winchester 1917

  1. #11
    Join Date
    Nov 2009
    Location
    Northern California
    Posts
    293

    Default

    Quote Originally Posted by chuckindenver View Post
    the 2 tone colors are from the ends being annealed..90% of all 1917,s will have this. sans a few rare early rifles. easier to see when parkerized then blue.
    Thanks, Chuck. I was wondering about the color differences myself

  2. #12
    Join Date
    Aug 2009
    Posts
    9,447

    Default

    Winchester had lots of parts left over after WW1 so they sporterised the M1917 and called it the model 30 which sold until 1940

  3. #13
    Join Date
    Nov 2009
    Location
    Northern California
    Posts
    293

    Default

    Was that Winchester or Remington?

  4. #14
    Join Date
    Aug 2009
    Posts
    358

    Default

    Quote Originally Posted by John Sukey View Post
    Winchester had lots of parts left over after WW1 so they sporterised the M1917 and called it the model 30 which sold until 1940
    Best to rethink that John . . . .it was Remington that came out with the model 30 . . . .remember?? --Jim

  5. #15
    Join Date
    Nov 2009
    Location
    Northern California
    Posts
    293

    Default

    I stuck a Weaver K4 on this one (didn't care for the United that came with it) and shot it today. The "crown" (or what a gunsmith might laughingly refer to as a crown) is scary looking.





    But even with the scary looking crown, it did ok..threw one to the 12o'clock and one went a bit wide

    Question...how much improvement could I expect from re-crowning it?

    6 180 gr Federal Powr-shoks @ 100 yards
    ...a fool and his money were lucky to get together in the first place...

  6. #16
    Join Date
    Aug 2009
    Location
    Eastern Missouri
    Posts
    4,838

    Default

    I think I might have it recrowned and see what it will do. Might be a tack driver.

  7. #17
    Join Date
    Nov 2009
    Location
    Northern California
    Posts
    293

    Default

    I recently got the barrel recrowned. The gunsmith recommended a very slight re cut and then recrowned the barrel.



    Much better than the old "crown"


    I hope to get to the range this week and see if there is an improvement.
    ...a fool and his money were lucky to get together in the first place...

  8. #18
    Join Date
    Nov 2009
    Location
    Northern California
    Posts
    293

    Default

    Got to the range yesterday for a quick session. Didn't get many shots downrange, but did shoot a few with the sported 1917.

    I was a little disappointed in the results...



    I can't blame the new crown...it looks good


    I'm not sure if I got everything back into the stock correctly...or if it needs a little firing to settle everything. There doesn't seem to be much up pressure on the barrel at the tip of the stock either...might have to shim the tang a bit.
    ...a fool and his money were lucky to get together in the first place...

  9. #19
    Join Date
    Aug 2009
    Location
    Oceanside, Ca
    Posts
    3,422

    Default

    I'd put some more round through it first, and then check the screws for tightness. See what results you get before fiddling with anything else.
    "No man's life, liberty, or property is safe, while Congress is in session." Mark Twain

  10. #20
    Join Date
    Dec 2009
    Location
    Monterey Indiana
    Posts
    2,078

    Default

    Dan, I think he was joking, at least I hope he is joking as that looks like its shooting damn good
    Once it has been decided to fight, one should do so to the very end, to conquer or perish...... Nothing smells better than the body of a dead enemy.

    The meek shall inherit the earth - in little 3x6 plots Robert Heinlein

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts